• Instagram
  • YouTube

  • Dani’s Blog
  • About
  • Things4You
  • Subscribe

#3dprinting

esk8 / I fell from my esk8 and it’s a good thing

March 29, 2019March 29, 2019 / Dani

It was my first. One moment I’m on the board, cruising through the campus, the other moment I’m on the ground, the board is upside down, and someone brings my…

Continue Reading
3dprinting carbon crash esk8 PLA

esk8 / Mini esk8 Remote with Thumb Control

December 21, 2018December 21, 2018 / Dani

The mini was my first ever remote, for an esk8, right along with the first esk8 attempt. (That’s the mini right there in the picture) View this post on Instagram…

Continue Reading
3dprinting esk8 mini

Projects / from spilled water to first clean sock

November 4, 2018June 19, 2020 / Dani

It went forward in “less than perfect way”, as some of the project often do. Puddles all around and the washer dancing on top of the bigger washer. Well, at…

Continue Reading
3dprinting design diy miniwasher washer workout

Projects / You can almost wash your clothes, almost

October 12, 2018October 12, 2018 / Dani

When you make something, there’s a point in time when everything comes together. Every little bit of hardware fits in just right, all the seams are closed, and it ticks…

Continue Reading
3dprinting carbon diy idea washer

Projects / dosimplecarbon – Small Washer for Workout Clothes – It’s moving now

October 5, 2018 / Dani

This progress update did not come as easy as expected, and I should have (probably) expected this.   So, I did not keep my promise to publish the updates weekly.…

Continue Reading
3dprinting carbon dosimplecarbon magnets washer workout

esk8 / How to Wire 6s BMS to Your 2x3s LiPo esk8

August 30, 2018 / Dani

This is my attempt to add simplicity to the short commuter board we are building now.   With v1 board, I had to take the batteries out of the enclosure,…

Continue Reading
3dprinting battery bms dosimplecarbon electric longboard esk8 longboard

esk8 / dosimplecarbon – The Big Promise?

August 9, 2018August 10, 2018 / Dani

How do you like your board?   My progress on the smaller 30” version got me loving it even more.   So far, the deck is assembled, and the enclosure…

Continue Reading
3dprinting dosimplecarbon electric longboard esk8 longboard tubes

esk8 / dosimplecarbon – first Q and A

August 2, 2018 / Dani

Those who see my boards for the first time inevitably ask me the same two questions:   Will it break if you jump on it? And, is PLA strong enough?…

Continue Reading
3dprinting carbon dosimplecarbon electric longboard esk8 longboard tubes

esk8 / DoSimpleCarbon v1 Board Revisited

July 12, 2018 / Dani

Now when the big version is finished, comes an opportunity to improve the very first board that we have built here.   The v1 was just that – a prototype…

Continue Reading
3dprinting battery carbon dosimplecarbon electric longboard esk8 frame lithium longboard tubes

esk8 / DoSimpleCarbon v2 on Thingiverse

July 5, 2018 / Dani

It is finally out there! Now you can make something original! Tell us about your experience!   Thing 2991709   As a last minute update I added a foot rest…

Continue Reading
18650 3dprinting carbon dosimplecarbon electric longboard esk8 lithium longboard tubes

Posts navigation

1 2

Recent Comments

  • Dani on How to do a simple FEM Analysis – The case of Slide Inline Frames
  • arianetrek on How to do a simple FEM Analysis – The case of Slide Inline Frames
  • Dani on First giveaway – dosimplecarbon
  • Dani on First giveaway – dosimplecarbon
  • EDWIN MUN on First giveaway – dosimplecarbon
Powered by WordPress | Theme: Latest by uXL Themes
 

Loading Comments...